Samples
Try before you commit. Order a $5 sample and see the real texture and color in your own space. Sample cost is credited toward your full roll purchase.
Order a sample →Project tools
Measure once.
Order smarter.
Estimate roll quantity, understand samples and get your project ready to install.
Roll calculator
How many rolls?
Every TWD roll is 20.9" x 393.7" (0.53 m x 10 m) — about 57 sq ft. Enter the wall area and we’ll add a practical installation allowance.
Shipping
We ship worldwide. Orders $499+ qualify for free The Wallpapers Depot Ground in LA, Orange County, and within 60 miles of those counties. Delivery is typically 3–7 days.
Installation
All our wallpapers use the paste-the-wall method — apply adhesive to the wall, not the paper. Check our step-by-step guide for a professional finish.
Installation guide →Need an installer?
Don't want to DIY? Get in touch and we'll help connect you with a professional wallpaper installer in your area.
Contact us →Measuring guide
How to measure
your wall.
Accurate measurements mean the right number of rolls, less waste and a perfect result. Here is how to measure for every wall type.
Standard wall
Measure the width and height of your wall. Add 2 to 4 inches to both dimensions as a cutting margin. This extra material is trimmed away during installation.
Sloped wall
Measure at the highest point for the height and the widest point for the width. Order based on these maximum dimensions; the excess is trimmed to follow the slope.
Multi-sloped wall
For walls with multiple angles, measure the longest horizontal and vertical spans. This ensures your wallpaper panels are large enough to cover every part of the wall.
Walls with doors or windows
Measure the full wall dimensions including doors and windows. Do not subtract openings from your measurement; cut around them during installation for a clean, continuous finish.
Multiple walls
Add the widths of all walls together to get the total width. Use the height of the tallest wall. This lets you order all the wallpaper you need in a single calculation.
Staircases
Measure the wall width and take two heights: the highest point and the lowest point. Use the highest measurement when ordering so every panel has enough material.
Installation guide
How to install
your wallpaper.
All Wallpaper Depot papers use the paste-the-wall method. No soaking, no pasting table. Here is the complete process from start to finish.
Preparation
1
Prepare the surface
Make sure the wall is smooth, clean and dry. Remove old wallpaper, fill any holes or cracks, and sand down rough areas. A properly prepared wall is the foundation of a professional finish.
2
Mix the wallpaper paste
Use a high-quality paste suitable for paste-the-wall application. Mix according to the manufacturer's instructions until smooth and lump-free. Allow it to rest for the recommended time before use.
Hanging
3
Check your panels are complete and in order
Lay out all panels and verify the print quality, quantity and sequence before you begin. Confirm that colors are consistent across rolls. Do not proceed if anything looks incorrect.
4
Mark a vertical line with a spirit level
Use a spirit level and pencil to draw a true vertical line where your first panel will go. This reference line ensures the first panel is perfectly straight, which keeps every subsequent panel aligned.
5
Apply paste to the wall, not the paper
Roll an even coat of paste directly onto the wall, covering an area slightly wider than one panel. Paste-the-wall application means the paper stays dry and is easier to handle and position.
6
Hang panels edge to edge
Align each panel to the previous one, butting edges together without overlapping. Match the pattern carefully at the seam. Work from the top of the wall downward, leaving a few inches of excess at the top and bottom.
7
Smooth from center outward
Use a wallpaper brush or smoothing tool to press the paper flat, working from the center of the panel toward the edges. This pushes out air bubbles and ensures even adhesion across the entire surface.
8
Trim excess with a sharp knife
Once the panel is positioned and smooth, use a sharp utility knife and a trim guide to cut away the excess material at the ceiling, baseboard, and around any doors, windows or outlets.
Recommended tools
What you will need
Bucket
Spirit level
Pencil
Wallpaper brush
Roller & tray
Ruler
Sharp knife
Trim guide
Sponge / cloth
Seam roller
Pro tips
Before you start
Allow drying time
Let the wallpaper dry undisturbed for at least 24 hours. Avoid opening windows or using fans in the room during this period. Controlled drying prevents seams from lifting.
Clean paste immediately
Wipe any paste from the wallpaper surface right away using a clean, damp cloth. Dried paste can leave marks that are difficult or impossible to remove later.
Small bubbles disappear
Do not worry about tiny air bubbles that appear during installation. They will flatten and vanish as the paste dries and the wallpaper contracts against the wall.